Sale!

DEIF SCM-1 | Serial Communication Module Core Category

Original price was: ¥999.00.Current price is: ¥888.00.

DEIF SCM-1 | Serial Communication Module Core Category

  • Exact Model: SCM-1 (Serial Communication Module)
  • OEM Brand: DEIF A/S
  • System Series: AGC / Delomatic 4 / Multi-line 2 Series Genset Controllers
  • Core Function: This plug-in serial interface card provides RS-485 / RS-232 Modbus RTU communication lines between DEIF generator controllers and plant PLC/SCADA supervision networks.
  • Module Type: Serial Communication Option Module
  • Defining Specs: Galvanically isolated RS-485 / RS-232 serial ports, 9.6 kbps to 115.2 kbps baud rate range, Modbus RTU / ASCII protocol support, internal bus slot mounting.
Category:

Description

DEIF SCM-1 | Serial Communication Module Core Category

 

Dynamic Product Introduction

Few power management glitches disrupt an offshore drilling rig or hospital backup power grid faster than a sudden communication loss between the generator control suite and the main building management system. Honestly, when a serial interface card drops off the Modbus loop during a load-sharing operation, control operators lose visibility over engine diagnostics, kilowatt load distribution, and breaker states. The DEIF SCM-1 resolves this critical monitoring gap by acting as a dedicated, galvanically isolated serial communication bridge inside DEIF Multi-line 2 and AGC controllers.

Engineered specifically for demanding marine and land-based power generation panels, this SCM-1 module handles high-speed register polling while shielding sensitive internal processor buses from field-induced electrical transients. In plant maintenance scenarios, swapping out a faulted or lightning-damaged communication card with a bench-verified SCM-1 restores real-time SCADA telemetry and remote control commands instantly—without requiring complex cabinet re-wiring or firmware overhauls.

SCM-1

SCM-1

Key Technical Specifications

  • Interface Standard: Dual RS-485 / RS-232 serial communication ports
  • Supported Protocols: Modbus RTU, Modbus ASCII, DEIF standard ASCII protocol
  • Baud Rate Options: Configurable from 9,600 bps up to 115,200 bps
  • Data Bits & Parity: 8 data bits; Odd, Even, or No Parity; 1 or 2 stop bits
  • Electrical Isolation: 500 V RMS galvanic isolation between serial terminals and internal controller logic
  • Connection Headers: Removable 5-pin screw terminal connector block
  • Bus Interface: Internal multi-pin edge connector for DEIF option slots (Option H8 / M4 dependent)
  • Power Supply: Powered directly through the internal DEIF controller backplane (+5 VDC / +24 VDC)
  • Operating Temperature Range: -25°C to +70°C ambient operating window
  • Compliance Standards: CE, UL listed, DNV-GL marine classification certified

 

Global Sourcing & Live-Test SOP (Transparency Core)

Sourcing secondary-market power management modules requires an absolute zero-trust verification strategy to guarantee network stability on critical power infrastructure. Inbound shipments of the DEIF SCM-1 undergo strict customs documentation tracing and microscopic board-level audits to verify authentic solder masks, trace integrity, and transceivers.

Once cleared into inventory, every SCM-1 module transitions directly to our specialized DEIF test bench. Technicians seat the card into an active DEIF AGC controller backplane connected to a 24 VDC auxiliary power network. We execute a 24-hour continuous communication loopback test across RS-485 ports using a Modbus master simulator polling over 500 registers per second. Signal rise times, termination resistance values, and isolation barriers are verified using a digital storage oscilloscope before sealing the unit in ESD-safe protective packaging prior to dispatch.

 

The Field Engineer’s Pitfall Guide

❗ Missing 120-Ohm Termination Resistors: Installing the SCM-1 at either physical end of an RS-485 network line without activating or wiring the 120-ohm bus termination resistor causes high-frequency signal reflections. I once spent six hours diagnosing intermittent Modbus CRC errors on a hospital gen-set system only to find an engineer forgot to switch on the line termination resistor at the SCM-1 terminal block.

❗ Polarity Inversion on RS-485 A/B Lines: Reversing the Data+ (A) and Data- (B) differential wiring connections on the SCM-1 screw terminals will prevent all network communication on that branch. Always double-check line voltage polarities with a multimeter (Data+ should sit slightly higher in voltage than Data- at idle state).

❗ Ground Loop Coupling via Shield Leads: Grounding the RS-485 cable shield at both the SCM-1 module and the remote PLC end creates a ground loop that can burn out the RS-485 transceiver chip during lightning surges. Always ground the communication shield at one end only (preferably at the master PLC panel).

 

Intent-Driven FAQ

Will I need to re-program my DEIF AGC controller after installing a new SCM-1 card? No, Modbus registers and port assignment settings are stored in the host controller memory; however, you must ensure the baud rate, slave ID, and parity settings in the DEIF USW (Utility Software) match your existing SCADA setup.

Can the SCM-1 card support simultaneous RS-232 and RS-485 connections? The SCM-1 module provides dedicated terminals for serial modes, but hardware configuration determines active communication routing; refer to your specific DEIF controller manual for dual-port firmware limits.

Are surplus DEIF SCM-1 modules provided with factory original packaging? Inventory conditions range from brand-new old stock (NOS) in original DEIF boxes to fully certified pre-owned surplus. Regardless of outer packaging, every SCM-1 card passes a complete 24-hour Modbus stress test before dispatch.

What causes persistent Modbus CRC error alarms on the SCADA screen after replacing an SCM-1? Persistent CRC errors typically point to a baud rate mismatch, mismatched parity settings (e.g., Even vs. None), unshielded cabling running near high-voltage generator leads, or a missing 120-ohm termination resistor.

What warranty coverage is included with a replacement DEIF SCM-1 module? Our secondary-market and surplus DEIF SCM-1 modules include a comprehensive 12-month operational warranty covering transceivers, internal bus communication, and component stability under standard operating conditions.

Business Card